Airbag & Safety Restraint Connector Solution
Requirements-led connector review for airbag, seat-belt pretensioner, occupant sensing and restraint control interfaces.
Industry
Automotive Electronics Supplier
Application
Airbag and Safety Restraint
Solution decision path
From application problem to connector selection
Use this route to turn an operating condition into technical requirements, suitable product families and a complete RFQ package.
01
Application problem
What operating condition is creating connector risk?
Safety restraint interfaces are application-specific and safety-critical. Selection requires an approved interface, terminal system, shorting or secondary-lock requirements, controlled process and customer validation rather than a visual match.
Define use case
02
Connector requirement
Which technical requirements must be confirmed first?
Application: airbag, pretensioner, occupant sensor or restraint control module / Interface: customer-approved keying, terminal, lock and mating geometry / Process: controlled crimp, insertion, retention, traceability and error prevention
Check requirements
03
Product route
Which product families should be reviewed for this solution?
2 Pin Sealed Automotive Sensor Connector / 3 Pin IP67 Automotive Sensor Connector / 0.64mm Automotive Female Terminal
Review products
04
RFQ evidence
What information should the buyer prepare before quotation?
Exact restraint function and vehicle location / Approved interface drawing and mating component / Terminal, shorting and secondary-lock requirements
Submit project RFQ
Application challenge
Customer problem
Safety restraint interfaces are application-specific and safety-critical. Selection requires an approved interface, terminal system, shorting or secondary-lock requirements, controlled process and customer validation rather than a visual match.
Requirements intake
Interface and keying comparison
Terminal and process review
Controlled sample planning
Connector requirements
Application
airbag, pretensioner, occupant sensor or restraint control module
Interface
customer-approved keying, terminal, lock and mating geometry
Process
controlled crimp, insertion, retention, traceability and error prevention
Approval
project drawing, validation plan and customer authorization required
Engineering review
Technical risks to confirm before product selection
These points help buyers understand why connector selection should be reviewed by application, not only by product name or pin count.
The products shown are starting points for requirements discussion and are not represented as approved SRS components.
A visual or part-number similarity check cannot establish suitability for an airbag or restraint application.
Shorting contacts, CPA/secondary locks, materials, process controls and validation requirements are customer- and system-specific.
RFQ information checklist
Exact restraint function and vehicle location
Approved interface drawing and mating component
Terminal, shorting and secondary-lock requirements
Wire, crimp, retention and traceability controls
Customer validation and approval process
Recommended products
Product options for this solution
Use these product records as a starting point. Final selection depends on the mating interface, electrical load, environment, cable and validation requirements.
2 Pin Sealed Automotive Sensor Connector
Sealed sensor connector
- Pin
- 2 Pin
- Voltage
- 24V
- Current
- 8A
- IP
- IP67
3 Pin IP67 Automotive Sensor Connector
Sealed sensor connector
- Pin
- 3 Pin
- Voltage
- 24V
- Current
- 8A
- IP
- IP67
0.64mm Automotive Female Terminal
Female terminal
- Pin
- 0.64mm
- Voltage
- 24V
- Current
- 5A
- IP
- Housing dependent
18 Pin Automotive ECU Connector
ECU connector
- Pin
- 18 Pin
- Voltage
- 24V
- Current
- 5A
- IP
- Application dependent
Manufacturing support
Engineering and production support
Support can be coordinated from requirement review and product matching through samples, tooling discussion, testing requirements and production preparation.
Requirement review
Connector selection
Tooling support
Sample testing
Mass production
Quality inspection
Solution FAQ
Are the related products automatically suitable for airbag systems?
No. They are shown only as requirement-discussion paths. Safety restraint use requires a customer-approved interface, process and validation program.
Can an SRS connector be cross-referenced from appearance?
No. Keying, shorting features, terminals, locks, materials, process controls and approved validation must be verified from controlled records.
Need this connection solution reviewed?
Send application, drawing, voltage, current, environment and annual demand. We will match product options and engineering requirements.